嵌入式开发者社区
标题:
omapl138 ARM核启动linux系统启动不了?
[打印本页]
作者:
小石
时间:
2017-4-9 11:22
标题:
omapl138 ARM核启动linux系统启动不了?
q+ E0 ^- d$ H
我用的是uboot通过nfs加载虚拟机上的uImage文件,但是启动到下面红色标记处,就不向下运行了,请教下是什么原因?
6 C4 f U- H y I, P- a: N J2 H' X
谢谢!
2 Y! z, v( m _+ Z& T
Ethernet init succeed!
8 @! }4 [# u! e9 @' I
DaVinci-EMAC
2 Y. l$ ~1 ]1 w3 r* ]( |
Hit any key to stop autoboot: 0
K/ o M9 [: Q- r" S$ @" n( \
Using DaVinci-EMAC device
7 C' h9 J9 C0 V5 G! X8 j/ c
TFTP from server 192.168.2.6; our IP address is 192.168.2.8
1 }& M# t2 z: I( u+ S
Filename 'uImage'.
9 W& F v3 Y) }* h; u8 f
Load address: 0xc0700000
. ~& d# T6 h: s! S2 q, ^
Loading: #################################################################
* i8 g9 H# a5 ?
#################################################################
8 @3 t5 ]1 [9 V& \/ Y& I
#################################################################
8 \- E" V7 W5 u& d- A/ w
##
1 a9 S5 e" A2 t& a
done
6 O; a0 `1 s- C1 n
Bytes transferred = 2885872 (2c08f0 hex)
: m n# x! f( Z$ m. ^ ]
## Booting kernel from Legacy Image at c0700000 ...
, z* J. m. ]8 t" q) o
Image Name: Linux-3.3.0+
/ ?9 o9 a) G( X9 g4 l3 c
Image Type: ARM Linux Kernel Image (uncompressed)
+ B; J$ k( p- c
Data Size: 2885808 Bytes = 2.8 MiB
+ u7 }5 A- M: C
Load Address: c0008000
$ l5 Z. @3 ^% m& Z* V0 u% Z
Entry Point: c0008000
1 p7 k4 |; C8 n# Y" k
Verifying Checksum ... OK
# c8 g p# X9 T7 Q+ c
Loading Kernel Image ... OK
. T; p: y K3 f0 y. g8 G0 k
OK
1 \: s5 T( \# g6 n( x
2 _# T. j& T; B3 R9 s: K; Y- g5 y
Starting kernel ...
, r. j' j* r, J
) x( y0 x( o- l7 X! T* G- X# T& ~
Uncompressing Linux... done, booting the kernel. //停在这里不运行了
& e4 K, Y. w. F# f
$ a U% m1 F h% p* \3 z0 k
- o Q- t( a' R. E7 ?3 R
* _7 h1 K7 e( H
作者:
human
时间:
2017-4-9 18:22
检查一下串口设置是否有问题,默认的打印串口是uart2
作者:
小石
时间:
2017-4-9 19:01
human 发表于 2017-4-9 18:22
' Y/ B* g* c3 D! j8 v* J5 N
检查一下串口设置是否有问题,默认的打印串口是uart2
: B* ]0 V" `! G2 p: z
应该不是串口问题吧,逼近之前有打印:
! e% [9 C5 P) E. y
Starting kernel ...
m; D) h( n6 Y# j- k) q
& b) K8 r* z& _7 ^
Uncompressing Linux... done, booting the kernel.
) w' r- r. D) U. _
8 [% y2 _0 H: A. l5 g! m
然后创龙给的用户手册是 用"da850_omapl138_tl_defconfig" linux配置,出现上面的问题,
9 n& q# \9 ]: u+ m, Y
然后我在 arch/arm/config/ 目录下 试了一下"da850_sdi_defconfig " 就可以继续向下运行了。
: p0 I/ E" P1 r. f4 t
. H; i" @# d# r! C3 V" W: O
我现在就找找串口的问题,感谢
欢迎光临 嵌入式开发者社区 (https://www.51ele.net/)
Powered by Discuz! X3.4